Fuel Instruments & Engineers Pvt. Ltd.


Dyanamic Balancing Machine Model - HDM
Get A Quote
Machines Model HDM are horizontal type universal hard bearing balancing machines provided with Microprocessor based measuring panel HDM-8500 for balancing different shapes of rotors like rotors of electrical machines, crankshafts, cylinders, gas compressors, flywheels, turbine rotors, rotors of centrifugal pumps and any other type of rotors of rotating machines.
These machines features a very simple operation. The working cycle is fully automatic. From safety point of view a double press push button starts machine, measures and stores, the unbalance values on DPMs for two planes simultaneously and stop machine ( with brake if machine is provided with electrical breaking facility.) The measuring cycle general is less than 10 seconds for normal rotors which can be accelerated within 5 seconds.
To have smooth and gradual acceleration models HDM - 3,000/- 7,000/- 10,000/- 20,000/-
are provided with slipring motors in order not to have damage to drive couplings as well other
rotating parts in drive systems like gears etc. The starting of these machines is done manually by cutting resistances of starter in 4 to 5 steps.
key-board facility provided on measuring panel for correct data feeding of rotor with 1 digit accuracy for itsdimensions like A, B, C, R1 & R2. Tolerance limits of both correction plans i.e.
tl1 and tl2 can be fed, so that when rotor is balanced within the limits respective LEDs glow
up, indicating no further correction necessary. For other details please refer 'Features of Measuring panel HDM-8500'.
The usable length of machine is established according to the longest roter to be balanced.
Extension beds can be supplied on request, which can be dded to standard bed of machine. It is also possible to install an additional bed ( Gap bed ) with a pit between this bed and standard bed of machine in order to balance rotors having its outside diameter exceeding swing over standard bed. Models HD-7,000- 10,000/ 20,000 are provided with fixed separate drives and hence gap-bed design is not possible.
Digital display for unbalance indication
Amount and angle of unbalance for both planes displayed on separate DPMs. Hence linear accuracy is very goos as compared to analog meter + /- 1 digit for amount and +/-1 degree for angle.
Digital display for RPM indication
A DPM is provided to indicate balancing speed continuously as a standard feature.
Auto Stop
No necessity to stop machine once started. It stops automatically after stabilization of unbalance results.
Simultaneous Indication
Amount and angle of unbalance in both planes displayed simultaneously and remains displayed (stored ) till next run. This totally eliminates operation of plane selector and reduces additional time for stabilization of readings in other plane.
Data of rotor dimensions and balancing tolerance i.e. values of A,B,C,R1,R2, t11,t12 are fed by key operation . Hence accuracy of data feeding is accurate up to 1 digit.
Tolerance Indicators
Separate LEDs are provided for both planes which glow when unbalance is reduced within balancing tolerance.
Auto Range
Depending upon whether unbalance amount is more or less a respective course or fine range gets automatically selected till rotor gets balanced within tolerance limits, Multiplier operation is totally eliminated
Data store
Data of various rotors can be stored against respective rotor type nos. Hence no need of measuring of rotor dimensions or rotor data feeding when repeat balancing operation required. Just call rotor type no. and machine is ready for balancing.
Self Check
  Panel is provided with ‘self-check’ mode which checks proper functioning of digital displays, LEDs is cyclic operation. This helps immediate fault detection.
  This is a microproceser based measuring panel suitable for FIE Hard Bearing Balancing Machine
Dynamic Balancing Machine Model
MODELS UNIT HDM-10 HDM-30 HDM-50 HDM-100 HDM-300 HDM-650 HDM-1000 HDM-3000 HDM-7000 HDM-10000 HDM-20000
Weight of rotor kg 0.5-10 1-30 2-50 3-100 10-300 20-650 10-1,000 30-3,000 70-7,000 100-10,000 200-20,000
Max. weight on each pedestal kg 7.5 22.5 30 75 180 480 600 1,800 5,250 6,000 12,000
Max. diameter of rotor over bed kg 600 600 600 1,000 1,000 1,200 1,600 2000 2400 2400 3000
Max. Distance measured from coupling end to extreme bearing center.  mm 480 480 1,100 1,350 1350 1650 1,650 2,400 3,300 3,300 3,200
Min. Distance between Roller bearing of pedestals mm 75 75 75 90 110 300 350 500 560 560 660
Rotor journal dia mm 5-50 5-20 5-20 15-80 20-120 20-120 25-140 35-200 55-300 55-300 70-300
Balancing speed (n) RPM 1,000 700 700 600 500 350 300-600 250-500 200-400 200-400 200-400
Power of drive motor HP 0.33 0.75 0.75 0.15 3 5 7.5 20
Acceleration Capability (GD2N2) kgm2n2 0.29x106 0.37x106 0.37x106 0.88x106 3.9x106 8.56x106 14.12x106 168x106 168x106 216x106 301x106
Minimum unbalance mass measured g 0.01 0.1 0.1 0.1 0.1 0.1 0.1 1 1 1 1
Maximum unbalance mass measured kg 4 4 4 4 4 4 4 40 40 40 40
Unbalance reduction ratio % 95 95 95 95 95 95 95 95 95 95 95
Minimum achievable unbalance per Rotor Weight (for max. weight or rotor) gmm/kg 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.
Designed by : MID   Hosted by : GID   Promoted by : PBD